Slow week

 At certain points in a build, progress comes down to courage as much as it does knowledge or determination.  Knowing what needs to be done, and generally how to do it still requires the courage to make i,rreversible cuts, decisions about placement, drilling holes in walls, etc, etc.  

I've let several of those things slide until now - I have multiple tasks, each of which require the courage to make happen.  

First, up front.  I was probably overly ambitious with the headboard design.  It came out just fine, but in the process, I buried several things in the background - all of which now need attention before I can seal it up.  I finally got the hinges for the headboard doors, and installed them.  Check.

I cut (and re-cut) and varnished the dividers that sit between the storage and utility bays in the headboard, cut and varnished the back wall of the bays, and sort of figured out what goes where in terms of power, ducts and connections in general.  Pics on the front end next week.  So it's now ready to seal up which should happen this weekend.

The other end of this project is the hatch.  I've left it for last just because it's, well, the hatch.  Several design elements were left to figure out as I went along, and now things like gasketing, final end caps and so on are coming back to haunt me.  

The good news is that the skeleton is screwed and glued, and it's reasonably square.  Outer skin will go on tomorrow (glue and staples, and then I will work on end caps and attaching the hurricane hinge.  

Other tasks for the weekend:  

• Sand and varnish the cabin sole (floor)
• Mount the heater and route ductwork to vents
• Cut roof skin, seal and install MaxxFan
• Continue work on corner trim

More pictures next week - promise.

Agile Development

Especially for those in the IT world, the term ¨Agile¨ is usually met with both joy and trepidation.  Done well, it's one of the best things that has every happened to project management, software development, and well, almost anything.  However, it's rarely done 'well', and we'll leave it at that since this is a family show.

This project is possibly the most agile project I've ever done.  Everything about it has been an iterative design.  Almost nothing is exactly as I originally sketched it out, and design goals have shifted as I learned new things.  There are also things like the A/C system I mentioned in an earlier post that drove a major change in the front end, and the ripple from *that* change has kept on giving all the way to the back of the trailer.  In some ways I wish I'd waited to order the inverter - I originally bought with the expectation that I could run the house AC unit on battery for a couple of hours a night and recharge either via solar or plug-in.  Since the new AC runs on 24vdc, I now have a 2500 watt inverter to run the Instant Pot, and to charge laptops.  Just a little overkill, I think.  But it's bought, paid for and too long out of the box to return, so I'll bolt it in anyway.

The board above will get screwed in to the back of the bay.  The batteries will mount on the floor, taking most of the clear space at the bottom.  What's not shown here (future post) is circuit protection, AC switching, the master switch, etc.  That's all going up above the counter where they can be accessed without performing contortionist routines.  And I still have to balance and assemble the battery pack and BMS - not hard, but somewhat tedious and it does require a certain amount of care to avoid arc welding with your fingers.  At the end of the day, I'll have 100aH 24volts of LiFePo4 battery stuffed behind the wall to power all the creature comforts.

 

It's really blue right now...

 

I feel like I need a little Christmas tree to put on top!

Tonight was a big step - the last major bit of aluminum (but not the last major bit of work) is on the trailer.  

I called it a wrap tonight with the panel on and secured with screws and clamps. Tomorrow I'll start over at the back, unclamp it, contact cement a section, get it glued down, and then do the other half/thirds.

The top panel is 5x10x.100, which is a bit heavier, but means there are no seams on the top from the hurricane hinge forward to the 'tongue box' - or what I'd planned to be the tongue box.  

To say there have been a few design changes along the way is being kind.  As mentioned in the last post, I had initially planned for a window air unit in the tongue/utility box.  Moving to a commercial box means I have a lot less complexity up front, but does mean I have a front panel to close up. 

Once the side panels were glued down, I used a jigsaw to get close - typ 1/4¨ and a trim router with a cheap import carbide bit to bring the panels down to the correct line.  One tip on the jigsaw - make sure you get the right blade - the very thin metal blade clogged up so quickly that it was unusable after only a foot of .040.  The 'thin' blade worked fine.  Vacuuming up all the bits of aluminum was a major effort!  And even though you see all the junk piled inside, I did protect the inside to keep the chips out when cutting the sides.

Next up - the front panel and the hatch.  Any bets which one is going to be more work??

Diamonds

 

Today was the start of one of the last major steps in the build - skinning the outside!

I chose to add diamond plate to the lower sides, and to the nose, wrapping back about 9 inches around the front.  I actually did this for a couple of reasons.  First, the diamond plate provides an exta layer of protection for the parts most likely to get rock chipped or dinged from things I can't control.  Second (and probably more important) I could not get a 5x12 sheet of .040 aluminum at anywhere close to a reasonable price or distance.  Since the trailer is about 123 inches long and 56 inches high, this allowed me to skin the trailer without any awkward seams.
If the weather cooperates, the outside could be all skinned up by Tuesday!

On other subjects, I've finally made a number of decsions about things like AC, heater position, and tongue box.  For anyone in IT or project management - this is hands down the most Agile project I've ever done.  The entire design process has been very iterative, making significant changes based on the learnings from the previous sprint.  It's almost literally run on two week sprints, I've had to assign 'story points' to tasks, the definition of 'done' keeps shifting based on progress from each sprint, and so on.  

One of the areas where this has been most apparent is air conditioning.  i thought I had this wired. I had been planning all along to use a small 5000 BTU window AC, sized the inverter to drive it easily, and laid out the headboard to accommodate it.  But I was struggling with mounting the thing in the tongue box, whether I should get a commercial one and surgically alter it, or build one.  At the same time, I kept seeing ads and videos about Zero Breeze.  So I started researching it, and liked what I read.  And it runs on 24 volts, so that really means the insta-pot is the only major use for the inverter!  NOW I have to string new wire from back to front.  I'm glad I buried a pull string in the wire-way.  I'll pull a new one along with the 10Gauge wire just in case there's something else that needs to go in.